Many people were trying to withdraw some form or another even if the patch is small or large project. However, what about face appears to be a simple job of sticking to a square or rectangular plates on a wall, soon becomes a challenge when obstacles appear awkward not to fall perfectly on the width of the tile edge or when shapes are cut. Obvious choice is to usually I tile smaller pieces, stick them around the barrier in a kind of mad mosaic fashion, we all know is very professional finish. Here are some tips that can be used to achieve professional results every time.
1. the right tool for the job
Like any craft, using the right tool for the job will not only make your work easier, but also will give you the best results. There are a variety of tools used by professional tillers; However, with all the basic tools needed to be sufficient for good results.
You definitely need:
Tile cutter (manual type)
Nibs tile: for cutting away small amounts of unwanted tile
Tile saw: as with manual saw hacksaw before
A tile
Notched Trowel: for spreading glue
Grout Spreader
Constructors
In the film measurement
Profile meter
Additional tools include:
Tile saw power (preferably water cooled)
A small grinder for cutting
Tile hole cutter stickiness
Rake tile: for removing grout between tiles, glue
Tile chisel to remove: for removing existing tiles
2. several tiles
Before buying tiles and you need to measure the amount of space. At first this may seem quite challenging. Although some professional tillers often tell at a glance how many squares are required skills that comes with years of experience. However, the easiest way is to measure the length and width of each section, and then multiply the width and length to give you the value/square meters. To divide into smaller rectangles embarrassing shapes and apply the equation. Measure each section in this way, and then add them all together to get the total area bmatr square. Always allow additional ten percent for wastage (five percent for the mosaic tiles).
3. on the surface
The surface should be free to be tiled, grassy sound physical (not decorated or cheese), stucco walls, now you can sign with sealant before spreading glue (follow the instructions on the product). Solid walls significantly should be destroyed using the appropriate packing dry plaster should be completely before retirement.
4. where to start
First, measure the distance across the area to tile or tiled sequence, this experiment will help you decide the best starting point. Usually it is best to place the tiles to allow for the cuts at both ends and not start with a square.
If they retire to the level of the surface of a bathroom or kitchen, then it is usually OK to use this as your initial, but be sure to measure vertical to predict how to finish in the top row, to avoid having to cut very small tracks at the end. Use the spaces below the first row that should help with easy adjustments and give the gap opened a key for the asphalt to catch.
5. on the level of
If not, they are from surface level, use the line at the level of the spirit and draw over the first line; Use this as your initial. You should repair the baton right on the wall to prevent sliding while setting up the first line of glue.
6. where do you cut
If you retire a whole room, start with the end of the wall from there when you enter the room, to the other walls. This cut from the edge (even if they are not ordered).
7. long stick up
Use the appropriate size notched spreader, evenly spread the square meters of horizontal adhesive. Bed tile, nitorim a little with pressure and even create consistent. Continue to process a particular attention to align the edges against the previous tile (s).
8. intervals
If you are using intervals, ensuring that they are located deep enough below the surface of the tile so that they are not visible after the graoting, or, if you have enough space, used on the outside of each joint tile Monday. Then you can completely remove them after the glue has set up (typically after an hour or two); Ensure that ?????? is set to strict before removing them. Clean excess glue is not between (and) the tiles before the glue set.
9. the best cuts
The easiest way to measure the cuts is to explore the Interior Glazed tile that is toward the wall, the end of the pre-formed is at the corner. Then mark the back of the tile in the tile fixed previously. Following the signs to the front of the square; You can always place a tile spacing before cropping.
10. get around things
When you cut around shapes embarrassing use profile meter to get the outline, select the square and with a measurement. Alternatively, create a cardboard square when you first and happy the match. Then place the square in a flat, even surface and use smooth movements still seen tile. Do not hurry or force the saw through the tile, just use the pressure enough to allow it to cut its natural rate. Patience is the key to not damage the tile.
If you prefer to give your work for retirement by a professional, North London, her Gordon Carpenter & building services do it, even. Visit the http://www.lagordoncarpentry.co.uk for more information and to see the range of services.
No comments:
Post a Comment