A good resource is the ceramic tiles typically for bathroom floors, range, and along the walls and even kitchens. Easy maintenance and durability of flooring that has made it popular for many people.
Tile flooring installation is not difficult, but requires some patience and preparation. Make sure that all materials and tools before you start the task. And the walls and floor tiles would involve, it is recommended that you first run. The floor tiles are usually thicker than the wall tiles so make sure that you are using the squares for the correct platform. .
Tools and materials for laying tiles
The tools required to install glass tile flooring are hotchni of the Carpenter's square, the helmet doesn't have, was grout, tape measure, pencils, its sponges, hammers, notched trowel. The materials required are tiles, tile, spackling compound, tile adhesives, silicone caulk and grout sealer.
Tiles and preparation
You must remove the old pavement is completely before installing new tiles. Ensure that the sub-floor strong and able to support the new tiles, 1 "thick. Since the heavy tiles must be installed on a flat, rigid surface. All the hits later in the graoting and can lead to cracking the tiles. If the floor is flat, covered with under layment-root tile. If you have a concrete floor, fix all holes, cracks. If you have, you can put the linoleum underlayment over it.
Remove all the trimmings and floor clean thoroughly. The surface must be free of wax, grease or debris. Use the membrane to water if the area is subject to moisture. Fibre-cement boards are most suitable for tile underlayment name in these cases.
Patterns and layouts
Patterns and the types of tiles are numerous, depending on how you want to be artistic. The two most common formats are Jack-??'? ' and ' bond '. While the former is composed of tiles laid like a chessboard, grout lines last offset for each row. Always centered tiles bathroom to look good and tidy.
Measure, the center of two opposite walls. Use these points to draw a chalk line across the length distribution of doubles. Then do the same with the other two walls by drawing a line is perpendicular to the other. Use a Carpenter's square to ensure that the center point is a square.
Dry-fit line of squares down two lines intersect. Keep spacing for grout joints. By laying out the tiles in this way, you will get an idea of what you can make adjustments. Work with some of the squares in full as possible and try to end up with less than half the width of the tile in areas where the walls meet.
Installing the tiles
For placing a tile from the intersection of the lines 2; Then, use the Guide as you work on the way out towards the walls every quarter. Spread the glue with notched edge of trowel, combing it out rising verse. You can add plastic gaps between tiles to keep straight lines grout. Remember to remove these after placing the tiles, but before they become the glue. Excess adhesive cleaning before drying it. Glue takes about 20-30 minutes to set up well.
After you have installed the number of rows of stones, set them into glue with tile leveler and a mallet. After you define all the stones all around the room and start the cut stones to fit around the perimeter of the room.
Cutting and ceramic tiles
Of course, all jobs will require some cropping flooring, cutting of tiles, so that they fit around the borders, obstacles, plumbing, wiring, window frames, pipe into this power, and so on. Plaid to adjust those indentures difficult and requires some patience and practice. You can use a tile cutter or small jobs, but a glasscutter for larger projects, you must have seen wet.
Pressure when using scoring tool, cutting, drilling tiles, but a little extra pressure can cause the tile crack or break.
To make the cuts at right angles with a glasscutter, a right to use a combination of the hedge. This should be done in line to achieve a smooth and even.
Repeated scoring lead crack of the tile.
Tiles must be snapped or hand with Tile nippers, tile hotchni or wet saw. Start and after measuring the size needs to be cut off. Always for wear safety goggles when using tiles.
The treatment is rough and jagged
Nippers, forceps or be used to remove jagged edges like a round will help smoothen rough edges. Cutting edge align, rub it against a sheet of aluminum oxide with 80 grit sandpaper, smoothen the edges to round.
Graoting joints
Grout mixture paste thick applied by forcing the grout between the tiles with floating rubber held a 45-degree angle. Hold, float almost vertically to the floor. Wipe away excess grout from the surface of the tiles. Use the toothbrush to design the grout. After 20 minutes, wipe any excess Grout with a humid sponge. Fill out a few cracks flexible silicon hmomsim tiles meet the counter the seams. Smoothen it with a sponge or a finger. Allow grout cure for a week and then apply the grout seal silicon with a small paintbrush to help prevent grout discoloration.
William Brister-[http://www.flooringworld.tv]-beautiful and durable
No comments:
Post a Comment